Post-supported extruded aluminum canopy systems engineered for wind and snow loads provide economical weather protection along pedestrian walkways and entrances.

Primary entries, transit shelters, covered walkways.

Requires ground support posts.

Tensioned exterior shading and weather protection using high-performance architectural fabrics. Systems are configured for attachment to building structures and coordinated with façade assemblies and adjacent construction.

Used at building entrances, storefronts, windows, walkways, and outdoor gathering areas for sun control, rain protection, and visual identity in commercial and institutional projects.

Not intended for locations requiring impact resistance, fire resistance, or continuous snow load capacity beyond fabric system design limits.

Fabric warranties vary by selected fabric manufacturer; extended warranties greater than one year may be available depending on fabric type.

Extruded aluminum sunshade systems with horizontal or vertical louvers designed to reduce solar heat gain and glare while enhancing facade appearance.

Window walls, façades, curtain walls.

Not intended as primary weather barrier.

Warranty terms are project-specific; extended warranties may be available depending on materials and finishes.

Wall-mounted aluminum canopy providing unobstructed overhead cover. Internally supported extruded aluminum canopy with steel support arms and integrated drainage provides streamlined weather protection without ground supports.

Main entries, storefront canopies.

Requires structurally capable wall substrate.

Overhead supported extruded aluminum canopy with built-in drainage and customizable fascia and decking provides durable weather protection at building entrances and service areas.

Building entrances, walkways, exterior transitions.

Not suitable where structural support is inadequate.

Steel palisade security fencing system with anti-climb picket profiles and mechanically fastened components designed for high-security perimeter applications. Vertical pickets attach to pre-punched horizontal rails using break-away nuts and anti-pry bolts, with replaceable individual pickets, anti-climb projections, and I-beam support posts for permanent installation.

Commercial and Industrial

See Warranty Information

StuccoDri is a water repellent, high performance, permeability reducing liquid admixture (PRA) designed for cementitious stucco. It is a liquid admixture that replaces water in the mixing process at a 1:1 ratio. Integral, permanent water resistance—built into the mix. Up to 120% permeability reduction on full-thickness stucco. Compatible with lath-applied and direct-applied stucco systems. Accepts traditional, properly applied exterior paints and coatings designed for stucco.

Exterior above-grade wall surfaces in commercial and residential construction, including stucco assemblies. Suitable for use in both new construction and remodeling projects.

Not intended to function as a waterproofing membrane or as a surface-applied treatment. Do not apply in standing water or to saturated substrates; use only where substrates are properly prepared and suitable for the intended installation conditions.

Corning® Med-X® LT Glass, Lemi-Thin radiation shielding/x-ray barrier. Meets Cat II Impact Ratings. Maximum finished size of up to 40" x 60". Registered as compliant with U.S. Food and Drug Administration (FDA) regulations. and McGrory Glass, Inc. is the only FDA Registered Medical Device Manufacturer; Repackager/Relabeler of FDA Registered radiation shielding glass. FDA Registered Material has a verified, traceable process linking the manufacturer to the processor to the installer to the project within the formalized format of FDA Registration. Traceability helps ensure compliance with medical device standards: at any point, from receipt to post-installation, each individual piece of Corning® Med-X® LT Glass can be traced back through its shipment, processing, and manufacture.

Corning® Med-X® Glass, lead, radiation shielding glass, dimensions up to 54" x 108". Optical Properties - Refractive Index nd: 1.76 Transmission % @ 550nm through 5mm path: ≥85.0 Mechanical Properties - Lead (Pb): 52% Barium (Ba): 17% Mechanical Properties - Density (g/cm3): 4.8 Knoop Hardness (kg/mm2): 409 Young’s Modulus (GPa): 62.6 Torsion Modulus (GPa): 24.8 Poisson’s Ratio: 0.26 Coefficient of Thermal Expansion (x10 -7 /°C): 78.8

ElectraView™, zero energy required for OBSCURE or CLEAR state. Energy Data: Input Power - 120VAC /60Hz Output Power - 48VAC /60Hz Energy Consumption - 0.3 watts/ ft2 power on | 0 Watts/ ft2 power off Power Quality - Film is protected by an isolation transformer, reducing spikes, harmonics, and noise when using ElectraView™ PDLC controller by McGrory. Operating Temperature - 0°-35°C INTERIOR ONLY

Doors and entrances, Office fronts, Hospital room dividers & Curtain walls, Emergency room / ICU sliding & breakaway doors, X-Ray privacy, Conference rooms, Laminated glass

Factory-formed cold-formed steel jamb and header system for framed openings, intended to replace built-up stud-and-track assemblies with a single-piece component. Manufactured from galvanized steel complying with ASTM A653 and designed in accordance with AISI S100, providing code-compliant structural support for door and window openings under the International Building Code (IBC).

Galvanized steel plate veneer anchor with vertical projecting leg protruding through continuous insulation to receive veneer triangle. Available in hot dip galvanized finish.

Masonry veneer anchor screw attached to stud framed, concrete, or masonry exterior walls. Use with or without seismic clips and continuous rods.

Install anchor before continuous wall insulation. Maximum 4.5 inch wide cavity with maximum 4.5 inch thick continuous insulation. Maximum 9 inch veneer triangle length.

Galvanized steel screw and washer anchor with projecting eye to receive hot dip galvanized steel wire tie. Available in polymer coated finish.

Masonry veneer anchor screw attached to metal and wood stud framed exterior walls with continuous insulation. Use with or without seismic clips and continuous rods.

Install anchor after continuous wall insulation. Maximum 6 inch sheathing plus insulation thickness. Maximum 7 inch veneer wire tie length.

Ladder style with projecting eyes, galvanized steel, horizontal joint reinforcing for masonry cavity wall joints. Available in standard, heavy duty, and extra heavy duty side and cross wire diameters with mill or hot dip galvanized finish.

Cavity walls with masonry veneer and concrete masonry backup at exterior walls. Use with loadbearing and non-loadbearing, ungrouted and vertically reinforced and grouted concrete masonry. Use with veneer hooks with or without seismic clips and continuous rods.

Maximum 12 inch concrete masonry wythe. Maximum 6 inch wide cavity with maximum 4 inch thick continuous insulation. Maximum 7 inch veneer hook length.

Galvanized steel triangle wire veneer tie fitted with dovetail head for insertion into dovetail slot. Available in hot dip galvanized finish.

Masonry veneer anchor for concrete and masonry substrates with or without continuous insulation. Use with or without seismic clips and continuous rods.

Requires dovetail slot cast into concrete substrate or surface mounted on concrete or masonry substrate. Maximum 5 inch dovetail triangle length.

Rebar Positioners are used to properly locate the rebar in the cores of the CMU.

Ladder style, galvanized steel, horizontal joint reinforcing for unit masonry joints. Available in standard, heavy duty, and extra heavy duty side and cross wire diameters with mill or hot dip galvanized finish.

Single wythe concrete masonry exterior walls and interior partitions. Use with loadbearing and non-loadbearing, ungrouted and vertically reinforced and grouted concrete masonry.

Maximum 12 inch concrete masonry wythe.

Type 304 stainless steel, self-adhered, laminated, flexible flashing with bonded butyl adhesive and release liner in 12 to 36 inch widths. Accessories include stainless steel termination bars, drip edges, prefabricated inside and outside corners, prefabricated end dams, and sealants.

Self-adhered masonry through wall flashing used with concrete, concrete masonry, and sheathing structural backup. Primer is not required.

Requires termination bar to secure top edge. Requires support across masonry cavity air space.

Life of wall warranty. 3GEN Masonry Products, Inc. (“3GEN”) warrants that its GENFLASH Membrane (“Product”) will be free from material defects that cause water penetration through the membrane for ten (10) years from the date of sale, subject to the terms, conditions, and limitations stated herein. This warranty applies solely to GENFLASH installed as an in-cavity wall flashing product to channel water out of weep holes, in accordance with 3GEN’s installation instructions. Other installation methods are explicitly excluded from this warranty.

Cellular polypropylene co-polymer vent to enable air flow and drainage of masonry cavity walls without insect intrusion. Available in six standard colors and two sizes to accommodate standard modular and jumbo brick head joints.

Replace brick masonry head mortar joint to create cavity wall weeps and vents. Install as weeps above flashing. Install as vents below flashing. Install with 1/8 inch set back from exterior wall face.

Prevent mortar droppings within cavity from clogging weeps.

Galvanized steel plate veneer anchor with projecting tab to receive veneer triangle. Available in hot dip galvanized finish.

Masonry veneer anchor screw attached to stud framed, concrete, or masonry exterior walls. Use with or without seismic clips and continuous rods.

Do not install anchor over continuous wall insulation. Maximum 6 inch wide cavity. Maximum 9 inch veneer triangle length.

Composite polyethylene sheet, self-adhered, flexible flashing with bonded clear adhesive in 4 to 36 inch widths. Accessories include stainless steel termination bars, drip edges, prefabricated inside and outside corners, prefabricated end dams, and sealants.

Self-adhered, self sealing, masonry through wall flashing used with concrete, concrete masonry, and sheathing structural backup. Primer is not required.

Requires termination bar to secure top edge. Requires support across masonry cavity air space.

3GEN Masonry Products, Inc. (“3GEN”) warrants that its GENFLASH Membrane (“Product”) will be free from material defects that cause water penetration through the membrane for ten (10) years from the date of sale, subject to the terms, conditions, and limitations stated herein. This warranty applies solely to GENFLASH installed as an in-cavity wall flashing product to channel water out of weep holes, in accordance with 3GEN’s installation instructions. Other installation methods are explicitly excluded from this warranty.

3, 5, or 7 oz copper sheet, laminated, flexible flashing bonded to polymeric fabric on both faces in 12 to 36 inch widths. Accessories include aluminum and stainless steel termination bars, stainless steel drip edges, prefabricated inside and outside corners, prefabricated end dams, and sealants.

Masonry through wall flashing used with concrete, concrete masonry, and sheathing structural backup.

Requires termination bar to secure top edge. Requires support across masonry cavity air space.

Life of wall warranty. 3GEN Masonry Products, Inc. (“3GEN”) warrants that its GENFLASH Membrane (“Product”) will be free from material defects that cause water penetration through the membrane for ten (10) years from the date of sale, subject to the terms, conditions, and limitations stated herein. This warranty applies solely to GENFLASH installed as an in-cavity wall flashing product to channel water out of weep holes, in accordance with 3GEN’s installation instructions. Other installation methods are explicitly excluded from this warranty.

Type 304 stainless steel, laminated, flexible flashing with bonded polymeric fabric backing in 12 to 36 inch widths. Accessories include stainless steel termination bars, drip edges, prefabricated inside and outside corners, prefabricated end dams, and sealants.

Masonry through wall flashing used with concrete, concrete masonry, and sheathing structural backup.

Requires termination bar to secure top edge. Requires support across masonry cavity air space.

Life of wall warranty. 3GEN Masonry Products, Inc. (“3GEN”) warrants that its GENFLASH Membrane (“Product”) will be free from material defects that cause water penetration through the membrane for ten (10) years from the date of sale, subject to the terms, conditions, and limitations stated herein. This warranty applies solely to GENFLASH installed as an in-cavity wall flashing product to channel water out of weep holes, in accordance with 3GEN’s installation instructions. Other installation methods are explicitly excluded from this warranty.

Dovetail shaped drainage mesh formed from open mesh, woven, structural, polymer strands. Available in four thicknesses ranging from 0.4 to 2 inches. Compressible to fit multiple cavity widths.

Fill masonry cavities above flashings to keep weep holes open by catching mortar droppings on two levels above weeps.

Prevent mortar droppings within cavity from clogging weeps.

Cold-rolled steel expanded metal lath system for exterior and interior plaster and stucco assemblies, incorporating integrated longitudinal track wires to increase stiffness and fastening alignment. Complies with ASTM C847 and ASTM A653, and is suitable for use where 2.5 lb/sy metal lath is specified, including reduced-furr 2.5/316 configurations for 1/2-inch stucco systems in accordance with applicable IBC and ASTM C1063 installation requirements.

Stone Veneer, Stucco

10 Year Limited Warranty