Steel insulation attachment plate designed to mechanically secure mineral wool insulation to wood, steel, or concrete substrates. Grip-Lok® MW Plate distributes clamping force across the insulation surface and accommodates mineral wool thicknesses up to 5 inches.

The Grip-Lok MW Plate secures up to 5ʺ mineral wool. It can be installed into any substrate, including wood, metal, or masonry. Made from mill galvanized steel to prevent corrosion. Unlike adhesive stick pins, the Grip-Lok MW plate provides permanent attachment of mineral wool to the substrate. Curled sides provide rigidity and prevent sharp edges.

Not intended for structural attachment or primary cladding support. Fastener type and embedment must be verified based on substrate and project wind load requirements. Confirm compatibility with specified air/water-resistive barrier and wall assembly components.

This warranty is provided in lieu of all other expressed or implied warranties, including warranties of merchantability or fitness for a particular purpose. TRUFAST is not responsible for consequential or incidental damages.

Thermally efficient structural cladding support system designed for exterior rainscreen assemblies installed over continuous insulation and air/water-resistive barriers. ProChannel Ci integrates Grip-Deck TubeSeal® technology to minimize penetrations and reduce air and water intrusion at fastening points while maintaining structural attachment of cladding supports. The hat channel support members can be installed horizontally or vertically to accommodate substrate conditions and wall assembly requirements.

ProChannel Ci Cladding Support system with Grip-Deck TubeSeal® technology is a thermally efficient structural exterior rainscreen wall cladding attachment system that is intended to minimize penetrations through the insulation and AWRB layers.

Not intended to replace primary air-barrier transitions or flashing details. Structural capacity, fastener selection, embedment, and spacing must be verified for substrate type, insulation thickness, cladding weight, and project wind loads. Confirm compatibility with specified insulation and AWRB materials.

This warranty is provided in lieu of all other expressed or implied warranties, including warranties of merchantability or fitness for a particular purpose. TRUFAST is not responsible for consequential or incidental damages.

2" diameter solid cap washer that attaches rigid insulation. Dual prongs enable pre-spotting for fast, on-the-wall fastener assembly. Flexible perimeter flattens without tearing insulation facer.

Thermal-Grip ci Prong Washers are for use with Grip-Deck® screws for continuous rigid insulation (ci) when insulation is being installed as the weather barrier or if insulation is being attached over a primary air barrier system.

This warranty is provided in lieu of all other expressed or implied warranties, including warranties of merchantability or fitness for a particular purpose. TRUFAST is not responsible for consequential or incidental damages.

Thermally efficient masonry veneer anchor engineered to secure brick veneer to structural substrate through continuous insulation. Thermal-Grip® Masonry Veneer Anchor reduces thermal bridging while helping maintain air- and water-barrier integrity at anchor penetrations.

The Thermal-Grip MVA attaches rigid insulation and anchors brick veneer to the supporting structure in masonry cavity wall construction.

Not intended for use outside published substrate, insulation thickness, or load capacity parameters. Anchor spacing, embedment, and design must be verified for project-specific wind loads and masonry veneer requirements. Confirm compatibility with specified air-barrier and insulation systems.

This warranty is provided in lieu of all other expressed or implied warranties, including warranties of merchantability or fitness for a particular purpose. TRUFAST is not responsible for consequential or incidental damages.

Flexible 2 inch diameter insulation washer designed to assist in the mechanical attachment of commercial building wrap and rigid foam insulation. Thermal-Grip® Flat Washer distributes load at the fastener head while helping to seal penetrations through the membrane.

TRUFAST®’s Thermal-Grip® Flat Washer aids in the mechanical attachment of commercial building wrap and rigid foam insulation.

Not intended for structural attachment or cladding support. Fastener type, embedment depth, and spacing must be verified based on substrate and project wind load requirements. Confirm compatibility with specified WRB and insulation materials.

This warranty is provided in lieu of all other expressed or implied warranties, including warranties of merchantability or fitness for a particular purpose. TRUFAST is not responsible for consequential or incidental damages.

Integrated plate fastener with sealing technology engineered for attachment of lath over continuous insulation while reducing air and water infiltration at blind fastener penetrations. Grip-Plate TubeSeal™ compresses and seals at the facer of the WRB or air-barrier located between the substrate and insulation layer.

The Grip-Plate TubeSeal™ fastener from TRUFAST® is designed to help seal blind fastener penetrations of your WRB and air-barrier when mechanically attaching lath over continuous insulation.

Not intended to replace primary air-barrier transitions, flashing, or detailing. Fastener selection, embedment, and spacing must be verified for substrate type, insulation thickness, and design wind loads. Confirm compatibility with specified WRB and air-barrier materials.

This warranty is provided in lieu of all other expressed or implied warranties, including warranties of merchantability or fitness for a particular purpose. TRUFAST is not responsible for consequential or incidental damages.

Insulation fastener with integrated sealing technology designed to reduce air and water infiltration at blind fastener penetrations through water-resistive and air barrier membranes. Mineral wool and rigid foam insulation must be mechanically attached, and often over a WRB or air-barrier. Thermal-Grip TubeSeal® provides mechanical attachment of continuous insulation while compressing and sealing at the WRB or air-barrier facer between the substrate and insulation layer.

The Thermal-Grip TubeSeal® fastener from TRUFAST® is designed to help seal blind fastener penetrations of your WRB and air-barrier when mechanically attaching continuous insulation.

This warranty is provided in lieu of all other expressed or implied warranties, including warranties of merchantability or fitness for a particular purpose. TRUFAST is not responsible for consequential or incidental damages.

Galvanized 1-1/4 inch steel plate washers engineered to provide secure mechanical attachment of lath, exterior gypsum sheathing, plaster bases, and stucco assemblies. Grip-Plate® Washers distribute load over a broader surface area to improve holding power and reduce fastener pull-through in cementitious and cladding support applications.

Grip-Plate Washers attach lath, exterior gypsum sheathing, and can also be used for plaster and stucco repair.

Not intended for structural load-bearing applications or primary framing connections. Verify compatibility with substrate type and specified fastener. Not recommended for use in highly corrosive environments without appropriate corrosion protection.

This warranty is provided in lieu of all other expressed or implied warranties, including warranties of merchantability or fitness for a particular purpose. TRUFAST is not responsible for consequential or incidental damages.

Single-screw veneer tie for anchoring masonry veneer to concrete backup walls, providing a 100 lb working load in both tension and compression at 0.05 inch deflection. Suitable for use in veneer wall assemblies detailed in accordance with applicable IBC and TMS 402/602 requirements.

Single-screw veneer tie for anchoring masonry veneer to cold-formed steel stud backup walls. Designed to resist 100 lb working load in both tension and compression at 0.05 inch deflection, suitable for use in veneer wall assemblies detailed in accordance with applicable IBC and TMS 402/602 requirements.

1-3/8” thick steel gauge door with a 0.20 U-Factor (R-Value 13.0).

Commercial applications that require a door with residential design and color options.

Available in sizes up to 20' wide x 16' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

2″ thick, thermally efficient residential steel garage door, featuring NeuFoam™ polyurethane insulation that fills 100% of the section’s interior.

For commercial applications that require residential design options and colors.

Available in sizes up to 24' wide x 16' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

2" thick, heavy-duty aluminum sectional rail and stile door. Increase thermal performance with ThermaXPS™.

Aluminum full view door for maximum visibility and design options.

Available in sizes up to 24' wide x 24' high.

Standard hardware warranty is one year. Section warranty against defects in material and workmanship is five (5) years. Window components warranty is (3) years.

3" thick, heavy-duty aluminum sectional rail and stile door with full-view glazing for large commercial openings.

Aluminum full view door with focus on increased durability and higher wind load ratings.

Available in sizes up to 24' wide x 24' high.

Standard hardware warranty is one year. Section warranty against defects in material and workmanship is five (5) years. Window components warranty is (3) years.

1-3/4" thick, aluminum sectional door, streamlined rail construction, with full-view glazing designed to maximize daylight and visibility.

Aluminum full view door for maximum visibility and design options.

Available in sizes up to 16' wide x 14' high.

Standard hardware warranty is one year. Section warranty against defects in material and workmanship is five (5) years. Window components warranty is (3) years.

Steel door constructed with 2" thick sections and nominal 24-gauge steel for standard-duty applications. Optional insulation is available to enhance thermal and acoustic performance while maintaining simplified configuration options.

Applications where a standard non-insulated door is needed.

Available in sizes up to 20' wide x 16' high.

Standard hardware warranty is one year. Section warranty against rust-through is ten years.

Heavy-duty commercial steel door constructed with 2" thick sections and 20-gauge steel for maximum durability in demanding environments. Optional insulation enhances thermal and acoustic performance, while ColorWave™ finishes provide coordinated color options.

Applications where a heavy-duty non-insulated door is required.

Available in sizes up to 32' wide x 24' high.

Standard hardware warranty is one year. Section warranty against rust-through is ten years.

Steel door constructed with 2" thick sections and 24-gauge steel to provide reliable performance across a broad range of applications. Optional insulation improves thermal and acoustic performance, and a wide selection of standard colors and ColorWave™ finishes supports design flexibility.

Applications where a standard 24ga non-insulated door is needed.

Available in sizes up to 32' wide x 24' high.

Standard hardware warranty is one year. Section warranty against rust-through is ten years.

Steel two-sided door, features a core of polystyrene insulation laminated between a 26-gauge interior steel and a 24-gauge exterior steel skin. The EC224 is available in white and is perfect for applications where thicker steel is specified.

Applications requiring a standard insulated door.

Available in sizes up to 24' wide and 16' high

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

Steel two-sided door, features a core of polystyrene insulation laminated between two high-strength 26-gauge steel skins. EC200 is available in six colors, two panel styles and optional windows to meet the need of any application.

Applications requiring a standard insulated door.

Available in sizes up to 24' wide x 16' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

Insulated sectional steel door with advanced thermal and structural performance for demanding environments. 3″ thick door with U-Factor of 0.19 (R-Value 24.54).

Ideal for applications requiring maximum thermal efficiency and long-term durability.

Available in sizes up to 40' wide x 24' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

Premium insulated sectional steel door with advanced thermal and structural performance for demanding environments. 3″ thick door with U-Factor of 0.19 (R-Value 24.54), 20-gauge exterior.

Applications requiring the highest thermal efficiency and durability.

Available in sizes up to 40' wide x 24' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

Heavy-duty, sectional, 20-gauge steel exterior door, 2″ thick with a U-Factor of 0.21 (R-Value 18.3).

Ideal for heavy duty applications.

Available in sizes up to 36' wide x 24' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

High-performance insulated sectional door with U-Factor of 0.17 (R-Value 18.3), 2″ thickness, is engineered for enhanced energy efficiency in commercial applications. Additional colors available.

Applications where an insulated door with a large selection of standard colors is needed.

Available in sizes up to 36' wide x 24' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

High-performance insulated sectional door with U-Factor of 0.21 (R-Value 18.3), 2″ thickness, is engineered for enhanced energy efficiency in commercial applications.

Applications with focus on high thermal efficiency and performance.

Available in sizes up to 36' wide x 24' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.