Thermally efficient structural cladding support system designed for exterior rainscreen assemblies installed over continuous insulation and air/water-resistive barriers. ProChannel Ci integrates Grip-Deck TubeSeal® technology to minimize penetrations and reduce air and water intrusion at fastening points while maintaining structural attachment of cladding supports. The hat channel support members can be installed horizontally or vertically to accommodate substrate conditions and wall assembly requirements.

ProChannel Ci Cladding Support system with Grip-Deck TubeSeal® technology is a thermally efficient structural exterior rainscreen wall cladding attachment system that is intended to minimize penetrations through the insulation and AWRB layers.

Not intended to replace primary air-barrier transitions or flashing details. Structural capacity, fastener selection, embedment, and spacing must be verified for substrate type, insulation thickness, cladding weight, and project wind loads. Confirm compatibility with specified insulation and AWRB materials.

Corrosion-resistant fasteners engineered for attachment of continuous insulation and cladding accessories to wood and steel framing. Grip-Deck® Hi-Lo Screws are designed for wood studs and light-gauge steel studs (typically 20 ga. to 25 ga.), while Grip-Deck® Self-Drilling Screws provide direct attachment to heavy-gauge steel studs (12 ga. through 18 ga.) without pre-drilling.

Grip-Deck® Screws are for use on wood, light gauge, or heavy gauge steel studs in various applications including attachment of continuous insulation, lath, or building wrap.

Steel insulation attachment plate designed to mechanically secure mineral wool insulation to wood, steel, or concrete substrates. Grip-Lok® MW Plate distributes clamping force across the insulation surface and accommodates mineral wool thicknesses up to 5 inches.

The Grip-Lok MW Plate secures up to 5ʺ mineral wool. It can be installed into any substrate, including wood, metal, or masonry. Made from mill galvanized steel to prevent corrosion. Unlike adhesive stick pins, the Grip-Lok MW plate provides permanent attachment of mineral wool to the substrate. Curled sides provide rigidity and prevent sharp edges.

Not intended for structural attachment or primary cladding support. Fastener type and embedment must be verified based on substrate and project wind load requirements. Confirm compatibility with specified air/water-resistive barrier and wall assembly components.

Galvanized 1-1/4 inch steel plate washers engineered to provide secure mechanical attachment of lath, exterior gypsum sheathing, plaster bases, and stucco assemblies. Grip-Plate® Washers distribute load over a broader surface area to improve holding power and reduce fastener pull-through in cementitious and cladding support applications.

Grip-Plate Washers attach lath, exterior gypsum sheathing, and can also be used for plaster and stucco repair.

Not intended for structural load-bearing applications or primary framing connections. Verify compatibility with substrate type and specified fastener. Not recommended for use in highly corrosive environments without appropriate corrosion protection.

Integrated plate fastener with sealing technology engineered for attachment of lath over continuous insulation while reducing air and water infiltration at blind fastener penetrations. Grip-Plate TubeSeal™ compresses and seals at the facer of the WRB or air-barrier located between the substrate and insulation layer.

The Grip-Plate TubeSeal™ fastener from TRUFAST® is designed to help seal blind fastener penetrations of your WRB and air-barrier when mechanically attaching lath over continuous insulation.

Not intended to replace primary air-barrier transitions, flashing, or detailing. Fastener selection, embedment, and spacing must be verified for substrate type, insulation thickness, and design wind loads. Confirm compatibility with specified WRB and air-barrier materials.

1-3/4" diameter washer for use with Grip-Deck® screws or nails. Dual prongs enable pre-spotting for on-the-wall screw assembly. The flexible perimeter flattens without tearing insulation face.

The Plasti-Grip ci Prong Washer is for use with fasteners to attach rigid insulation (EPS, XPS, ISO, etc.) over a primary air barrier. Attaches EPS foam for EIFS synthetic wall systems. Compatible with a nail gun, hammer, or screw gun.

Flexible 2 inch diameter insulation washer designed to assist in the mechanical attachment of commercial building wrap and rigid foam insulation. Thermal-Grip® Flat Washer distributes load at the fastener head while helping to seal penetrations through the membrane.

TRUFAST®’s Thermal-Grip® Flat Washer aids in the mechanical attachment of commercial building wrap and rigid foam insulation.

Not intended for structural attachment or cladding support. Fastener type, embedment depth, and spacing must be verified based on substrate and project wind load requirements. Confirm compatibility with specified WRB and insulation materials.

Thermally efficient masonry veneer anchor engineered to secure brick veneer to structural substrate through continuous insulation. Thermal-Grip® Masonry Veneer Anchor reduces thermal bridging while helping maintain air- and water-barrier integrity at anchor penetrations.

The Thermal-Grip MVA attaches rigid insulation and anchors brick veneer to the supporting structure in masonry cavity wall construction.

Not intended for use outside published substrate, insulation thickness, or load capacity parameters. Anchor spacing, embedment, and design must be verified for project-specific wind loads and masonry veneer requirements. Confirm compatibility with specified air-barrier and insulation systems.

Insulation fastener with integrated sealing technology designed to reduce air and water infiltration at blind fastener penetrations through water-resistive and air barrier membranes. Mineral wool and rigid foam insulation must be mechanically attached, and often over a WRB or air-barrier. Thermal-Grip TubeSeal® provides mechanical attachment of continuous insulation while compressing and sealing at the WRB or air-barrier facer between the substrate and insulation layer.

The Thermal-Grip TubeSeal® fastener from TRUFAST® is designed to help seal blind fastener penetrations of your WRB and air-barrier when mechanically attaching continuous insulation.

2" diameter solid cap washer that attaches rigid insulation. Dual prongs enable pre-spotting for fast, on-the-wall fastener assembly. Flexible perimeter flattens without tearing insulation facer.

Thermal-Grip ci Prong Washers are for use with Grip-Deck® screws for continuous rigid insulation (ci) when insulation is being installed as the weather barrier or if insulation is being attached over a primary air barrier system.