The MaxTrak System allows the top of the wall stud to float within the track legs. This connection allows for vertical live load movement of the primary structure without transferring axial loads to the wall studs.

Provides joint protection for up to 1" with UL 2079 Class II or III Movement Capabilities. Two solid legs supporting "free floating" studs per listed assemblies in UL Fire Resistance Directory. A 2mm thickness of cured intumescent material adhered to metal profiles provides air and smoke seals. When exposed to heat above 375 degrees Fahrenheit, the intumescent material expands up to 35 times its size. This provides protection from heat and flame passage during a fire event.

Profile with two solid legs with firestop on both sides. Composite Firestop Deflection Track System for use in fire-rated wall assemblies. Two solid legs supporting “free floating” studs.

Provides joint protection for up to 1" with UL 2079 Class II or III Movement Capabilities. Legs with slots spaced 1" o.c. for positive attachment of studs per listed assemblies in UL Fire Resistance Directory. A 2mm thickness of cured intumescent material adhered to metal profiles provides air and smoke seals. When exposed to heat above 375 degrees Fahrenheit, the intumescent material expands up to 35 times its size. This provides protection from heat and flame passage during a fire event.

Composite Firestop/Framing for use in fire-resistant joint systems in or between fire-resistance-rated walls and floor/ceiling or roof/ceiling assemblies.

Ladder style, galvanized steel, horizontal joint reinforcing for unit masonry joints. Available in standard, heavy duty, and extra heavy duty side and cross wire diameters with mill or hot dip galvanized finish.

Single wythe concrete masonry exterior walls and interior partitions. Use with loadbearing and non-loadbearing, ungrouted and vertically reinforced and grouted concrete masonry.

Maximum 12 inch concrete masonry wythe.

Galvanized steel screw and washer anchor with projecting eye to receive hot dip galvanized steel wire tie. Available in polymer coated finish.

Masonry veneer anchor screw attached to metal and wood stud framed exterior walls with continuous insulation. Use with or without seismic clips and continuous rods.

Install anchor after continuous wall insulation. Maximum 6 inch sheathing plus insulation thickness. Maximum 7 inch veneer wire tie length.

Galvanized steel triangle wire veneer tie fitted with dovetail head for insertion into dovetail slot. Available in hot dip galvanized finish.

Masonry veneer anchor for concrete and masonry substrates with or without continuous insulation. Use with or without seismic clips and continuous rods.

Requires dovetail slot cast into concrete substrate or surface mounted on concrete or masonry substrate. Maximum 5 inch dovetail triangle length.

Ladder style with projecting eyes, galvanized steel, horizontal joint reinforcing for masonry cavity wall joints. Available in standard, heavy duty, and extra heavy duty side and cross wire diameters with mill or hot dip galvanized finish.

Cavity walls with masonry veneer and concrete masonry backup at exterior walls. Use with loadbearing and non-loadbearing, ungrouted and vertically reinforced and grouted concrete masonry. Use with veneer hooks with or without seismic clips and continuous rods.

Maximum 12 inch concrete masonry wythe. Maximum 6 inch wide cavity with maximum 4 inch thick continuous insulation. Maximum 7 inch veneer hook length.

Cellular polypropylene co-polymer vent to enable air flow and drainage of masonry cavity walls without insect intrusion. Available in six standard colors and two sizes to accommodate standard modular and jumbo brick head joints.

Replace brick masonry head mortar joint to create cavity wall weeps and vents. Install as weeps above flashing. Install as vents below flashing. Install with 1/8 inch set back from exterior wall face.

Prevent mortar droppings within cavity from clogging weeps.

Composite polyethylene sheet, self-adhered, flexible flashing with bonded clear adhesive in 4 to 36 inch widths. Accessories include stainless steel termination bars, drip edges, prefabricated inside and outside corners, prefabricated end dams, and sealants.

Self-adhered, self sealing, masonry through wall flashing used with concrete, concrete masonry, and sheathing structural backup. Primer is not required.

Requires termination bar to secure top edge. Requires support across masonry cavity air space.

3GEN Masonry Products, Inc. (“3GEN”) warrants that its GENFLASH Membrane (“Product”) will be free from material defects that cause water penetration through the membrane for ten (10) years from the date of sale, subject to the terms, conditions, and limitations stated herein. This warranty applies solely to GENFLASH installed as an in-cavity wall flashing product to channel water out of weep holes, in accordance with 3GEN’s installation instructions. Other installation methods are explicitly excluded from this warranty.

Type 304 stainless steel, self-adhered, laminated, flexible flashing with bonded butyl adhesive and release liner in 12 to 36 inch widths. Accessories include stainless steel termination bars, drip edges, prefabricated inside and outside corners, prefabricated end dams, and sealants.

Self-adhered masonry through wall flashing used with concrete, concrete masonry, and sheathing structural backup. Primer is not required.

Requires termination bar to secure top edge. Requires support across masonry cavity air space.

Life of wall warranty. 3GEN Masonry Products, Inc. (“3GEN”) warrants that its GENFLASH Membrane (“Product”) will be free from material defects that cause water penetration through the membrane for ten (10) years from the date of sale, subject to the terms, conditions, and limitations stated herein. This warranty applies solely to GENFLASH installed as an in-cavity wall flashing product to channel water out of weep holes, in accordance with 3GEN’s installation instructions. Other installation methods are explicitly excluded from this warranty.

3, 5, or 7 oz copper sheet, laminated, flexible flashing bonded to polymeric fabric on both faces in 12 to 36 inch widths. Accessories include aluminum and stainless steel termination bars, stainless steel drip edges, prefabricated inside and outside corners, prefabricated end dams, and sealants.

Masonry through wall flashing used with concrete, concrete masonry, and sheathing structural backup.

Requires termination bar to secure top edge. Requires support across masonry cavity air space.

Life of wall warranty. 3GEN Masonry Products, Inc. (“3GEN”) warrants that its GENFLASH Membrane (“Product”) will be free from material defects that cause water penetration through the membrane for ten (10) years from the date of sale, subject to the terms, conditions, and limitations stated herein. This warranty applies solely to GENFLASH installed as an in-cavity wall flashing product to channel water out of weep holes, in accordance with 3GEN’s installation instructions. Other installation methods are explicitly excluded from this warranty.

Galvanized steel plate veneer anchor with vertical projecting leg protruding through continuous insulation to receive veneer triangle. Available in hot dip galvanized finish.

Masonry veneer anchor screw attached to stud framed, concrete, or masonry exterior walls. Use with or without seismic clips and continuous rods.

Install anchor before continuous wall insulation. Maximum 4.5 inch wide cavity with maximum 4.5 inch thick continuous insulation. Maximum 9 inch veneer triangle length.

Galvanized steel plate veneer anchor with projecting tab to receive veneer triangle. Available in hot dip galvanized finish.

Masonry veneer anchor screw attached to stud framed, concrete, or masonry exterior walls. Use with or without seismic clips and continuous rods.

Do not install anchor over continuous wall insulation. Maximum 6 inch wide cavity. Maximum 9 inch veneer triangle length.

Type 304 stainless steel, laminated, flexible flashing with bonded polymeric fabric backing in 12 to 36 inch widths. Accessories include stainless steel termination bars, drip edges, prefabricated inside and outside corners, prefabricated end dams, and sealants.

Masonry through wall flashing used with concrete, concrete masonry, and sheathing structural backup.

Requires termination bar to secure top edge. Requires support across masonry cavity air space.

Life of wall warranty. 3GEN Masonry Products, Inc. (“3GEN”) warrants that its GENFLASH Membrane (“Product”) will be free from material defects that cause water penetration through the membrane for ten (10) years from the date of sale, subject to the terms, conditions, and limitations stated herein. This warranty applies solely to GENFLASH installed as an in-cavity wall flashing product to channel water out of weep holes, in accordance with 3GEN’s installation instructions. Other installation methods are explicitly excluded from this warranty.

Dovetail shaped drainage mesh formed from open mesh, woven, structural, polymer strands. Available in four thicknesses ranging from 0.4 to 2 inches. Compressible to fit multiple cavity widths.

Fill masonry cavities above flashings to keep weep holes open by catching mortar droppings on two levels above weeps.

Prevent mortar droppings within cavity from clogging weeps.

• ASTM C494 Type S Certified
• Each batch pre-tested for performance
• HPD (Health Product Declaration) Certified
• EPD (Environmental Product Declaration) Certified
• Lifetime moisture failure warranty
• Warranted to 100% RH per ASTM F2170
• Warranted to 25 lbs/1000 sf/24 hours
• Separate warranty for adhesion
• It is the only concrete moisture vapor reduction admixture with cross-compatibility performance warranty with a leading adhesive manufacturer

MVRA 900 addresses concerns over concrete moisture vapor emission negatively impacting flooring, roofing, or coatings directly adhered to concrete substrate surfaces.

Requires compliance with ASTM F710 surface preparation and adhesive bond test.

Enhanced operational efficiency and quality control with liquid integral waterproofing for watertight concrete. CWPA 800 is NSF 61 and 372 Certified, and HPD and EPD Compliant.

• ASTM C494 Type S Certified
• Each batch pre-tested for performance
• HPD Certified (Health Product Declaration)
• EPD Certified (Environmental Product Declaration)
• Does not promote corrosion
• Completely blocks water migration through concrete CRD C48-92 and DIN 1048
• Enhanced durability
• Meets specifications for PRAN and PRAH (ACI 212.3R-10)
• Air entrainment compatible
• Minimal effect on set time in normal ambient environment

Keep your team organized and on track with Part3 — the construction administration software of choice for architects, engineers, and owners.‍

Used on exterior applications like commercial storefront, low rise curtain/window wall, windows etc.

Used on exterior applications like curtain wall, windows etc.

20-Year Color and Gloss Warranty