60-mil self-adhered fleece-backed thermoplastic polyolefin (TPO) roofing membrane with heat-weldable seams and factory-applied pressure-sensitive adhesive. Polyester-reinforced TPO sheet is formulated without liquid or polymeric plasticizers. Fleece backing improves substrate compatibility, accommodates minor surface irregularities, and increases cushioning, puncture resistance, and hail resistance. May reduce total installed cost in recover applications by minimizing tear-off and additional separation layers.
Sustainability / Performance Resistant to mildew, bacteria, and algae growth to help maintain high solar reflectivity and support reduced cooling loads and mitigation of urban heat island effects. Manufactured without plasticizers or chlorinated compounds.

Used in low-slope roofing systems for new construction and re-roofing applications. Used in fully adhered roofing systems and recover applications over approved existing roof assemblies, including smooth built-up roofing and other compatible substrates. Suitable for projects requiring increased puncture resistance, improved wind uplift performance, or installation over irregular surfaces.

Not intended for roofing assemblies outside thermoplastic single-ply systems or installations that do not comply with manufacturer requirements for substrate preparation, temperature conditions, and seam welding. Performance depends on proper substrate evaluation and installation in accordance with manufacturer guidelines.

Reinforced PVC decking membrane for high-traffic balcony and roof deck applications. Formulated for UV stability, chemical resistance, stain resistance, and slip resistance. Functions as both exposed walking surface and waterproofing layer for occupied exterior deck assemblies.

Balconies, terraces, roof decks, podium decks, and other pedestrian traffic surfaces requiring exposed waterproofing and slip-resistant performance.

Not intended for vehicular traffic; confirm structural deck slope and drainage provisions, and verify compatibility with underlying substrates and flashing components prior to specification.

Thermoplastic single-ply roofing membrane manufactured with DuPont™ Elvaloy® KEE (ketone ethylene ester) polymer. KEE polymer remains chemically bound within the membrane, minimizing plasticizer migration and maintaining flexibility and toughness over time, including in extreme climates.

Used in mechanically attached, fully adhered, ballasted, and vegetated (green roof) roofing systems. Reinforced membranes are available with smooth backing or fleece backing to accommodate various roof assembly types.

Compatible substrates and manufacturer-approved fastening or bonding adhesives required. Mechanically attached systems may not be suitable where deck penetration is restricted or where higher wind uplift performance is required without fully adhered installation. Fully adhered applications depend on proper adhesive selection and substrate preparation.

Thermoplastic single-ply roofing membrane formulated with DuPont™ Elvaloy® KEE (ketone ethylene ester) polymer. KEE polymer remains chemically bound within the membrane to minimize plasticizer migration and maintain flexibility over time. Fleece backing improves adhesion to irregular substrates, provides cushioning, and increases puncture resistance in adhered roof assemblies.

Suitable for mechanically attached, fully adhered, ballasted, and vegetated (green roof) roofing assemblies. Reinforced membranes are available with smooth backing for standard installations or fleece backing for adhered systems and compatible substrates.

For fully adhered applications only; not intended for mechanically attached systems. Compatible substrates and manufacturer-approved asphalt or adhesive required; unsuitable where substrate conditions prevent proper adhesion.

60, 72, or 80-mil polyester-reinforced PVC thermoplastic membrane with factory-laminated fleece backing. Fleece layer accommodates minor substrate irregularities, provides separation, reducing the need for slip sheets in approved re-roofing applications.

Used in mechanically attached or fully adhered roofing systems, including re-roofing over approved existing roof assemblies. Adhered installations using water-based PVC substrate adhesive can achieve FM Class 1-270 over lightweight concrete where high wind uplift resistance is required.

Not intended for roofing assemblies outside mechanically attached or fully adhered PVC single-ply systems. Substrate must be dry and structurally sound; fleece backing accommodates minor surface irregularities but does not bridge significant defects. Verify compatibility with asphaltic or chemical exposures where applicable. Seams must be heat welded in accordance with manufacturer requirements.

Thermoplastic PVC single-ply roofing membrane reinforced with polyester scrim and formulated with UV inhibitors for long-term weather resistance. Heat-welded seams create permanent watertight bonds stronger than the membrane itself, providing durable performance in demanding environments and across wide temperature ranges. Applicable PVC membranes are 100% recyclable at end of service life.

Used in low-slope roofing systems requiring mechanically attached, adhered, or other thermoplastic membrane assemblies. Suitable for projects where resistance to weather exposure, contaminants, and temperature fluctuations is required.

Substrate must be concrete, approved insulation and cover boards, or approved existing roof assemblies compatible with PVC roofing membranes. Separation required over asphaltic, bituminous, or polystyrene substrates. Reflective surface may not be appropriate where heat gain is desired. Seams must be heat welded in accordance with manufacturer requirements to maintain watertight performance.

Thermoplastic polyolefin (TPO) single-ply roofing membrane combining the weather resistance of ethylene-propylene rubber with the heat-weldable properties of polypropylene. Formulated without liquid or polymeric plasticizers to provide long-term weather resistance and membrane stability.

Low-slope roofing systems for new construction and reroofing where heat-welded seams and thermoplastic membrane performance are required.

Not intended for high-solvent or grease-laden exposure without confirmed compatibility; verify wind uplift assembly ratings, fire classification, and chemical resistance for project-specific conditions prior to specification.

60-mil self-adhered thermoplastic polyolefin (TPO) roofing membrane with heat-weldable seams and factory-applied pressure-sensitive adhesive. Combines TPO weathering performance with a 100 percent solids hot-melt adhesive to reduce VOC and odor concerns while maintaining welded seam integrity.

Used in low-slope roofing assemblies where a self-adhered installation is preferred to reduce fasteners and simplify installation. Supplied in 5- and 10-foot widths (50- and 100-foot rolls) with an uncoated selvage edge for hot-air welded field seams and a dual-sided silicon-coated release liner for controlled installation.

Not intended for roofing assemblies requiring mechanical attachment in lieu of adhesive bonding. Membrane performance depends on proper substrate compatibility and installation in accordance with manufacturer requirements, including hot-air welding of seams.

Extruded thermoplastic roof rib component designed to replicate the appearance of traditional standing seam metal roofing when used with Flex PVC roofing membranes. The rib profile is hot air welded to the membrane surface, providing a durable, integrated aesthetic feature without compromising the watertight roofing system.

Used on PVC single-ply roofing systems where the appearance of standing seam metal roofing is desired. Ribs can be welded at custom spacing and layouts to achieve project-specific architectural designs. Available in a range of colors coordinated with Flex PVC membranes.

Not intended for roofing systems other than compatible PVC membrane assemblies or installations that do not follow manufacturer welding and layout requirements.