1-3/8” thick steel gauge door with a 0.20 U-Factor (R-Value 13.0).

Commercial applications that require a door with residential design and color options.

Available in sizes up to 20' wide x 16' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

2″ thick, thermally efficient residential steel garage door, featuring NeuFoam™ polyurethane insulation that fills 100% of the section’s interior.

For commercial applications that require residential design options and colors.

Available in sizes up to 24' wide x 16' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

2" thick, heavy-duty aluminum sectional rail and stile door. Increase thermal performance with ThermaXPS™.

Aluminum full view door for maximum visibility and design options.

Available in sizes up to 24' wide x 24' high.

Standard hardware warranty is one year. Section warranty against defects in material and workmanship is five (5) years. Window components warranty is (3) years.

3" thick, heavy-duty aluminum sectional rail and stile door with full-view glazing for large commercial openings.

Aluminum full view door with focus on increased durability and higher wind load ratings.

Available in sizes up to 24' wide x 24' high.

Standard hardware warranty is one year. Section warranty against defects in material and workmanship is five (5) years. Window components warranty is (3) years.

1-3/4" thick, aluminum sectional door, streamlined rail construction, with full-view glazing designed to maximize daylight and visibility.

Aluminum full view door for maximum visibility and design options.

Available in sizes up to 16' wide x 14' high.

Standard hardware warranty is one year. Section warranty against defects in material and workmanship is five (5) years. Window components warranty is (3) years.

Steel door constructed with 2" thick sections and nominal 24-gauge steel for standard-duty applications. Optional insulation is available to enhance thermal and acoustic performance while maintaining simplified configuration options.

Applications where a standard non-insulated door is needed.

Available in sizes up to 20' wide x 16' high.

Standard hardware warranty is one year. Section warranty against rust-through is ten years.

Heavy-duty commercial steel door constructed with 2" thick sections and 20-gauge steel for maximum durability in demanding environments. Optional insulation enhances thermal and acoustic performance, while ColorWave™ finishes provide coordinated color options.

Applications where a heavy-duty non-insulated door is required.

Available in sizes up to 32' wide x 24' high.

Standard hardware warranty is one year. Section warranty against rust-through is ten years.

Steel door constructed with 2" thick sections and 24-gauge steel to provide reliable performance across a broad range of applications. Optional insulation improves thermal and acoustic performance, and a wide selection of standard colors and ColorWave™ finishes supports design flexibility.

Applications where a standard 24ga non-insulated door is needed.

Available in sizes up to 32' wide x 24' high.

Standard hardware warranty is one year. Section warranty against rust-through is ten years.

Steel two-sided door, features a core of polystyrene insulation laminated between a 26-gauge interior steel and a 24-gauge exterior steel skin. The EC224 is available in white and is perfect for applications where thicker steel is specified.

Applications requiring a standard insulated door.

Available in sizes up to 24' wide and 16' high

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

Steel two-sided door, features a core of polystyrene insulation laminated between two high-strength 26-gauge steel skins. EC200 is available in six colors, two panel styles and optional windows to meet the need of any application.

Applications requiring a standard insulated door.

Available in sizes up to 24' wide x 16' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

Insulated sectional steel door with advanced thermal and structural performance for demanding environments. 3″ thick door with U-Factor of 0.19 (R-Value 24.54).

Ideal for applications requiring maximum thermal efficiency and long-term durability.

Available in sizes up to 40' wide x 24' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

Premium insulated sectional steel door with advanced thermal and structural performance for demanding environments. 3″ thick door with U-Factor of 0.19 (R-Value 24.54), 20-gauge exterior.

Applications requiring the highest thermal efficiency and durability.

Available in sizes up to 40' wide x 24' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

Heavy-duty, sectional, 20-gauge steel exterior door, 2″ thick with a U-Factor of 0.21 (R-Value 18.3).

Ideal for heavy duty applications.

Available in sizes up to 36' wide x 24' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

High-performance insulated sectional door with U-Factor of 0.17 (R-Value 18.3), 2″ thickness, is engineered for enhanced energy efficiency in commercial applications. Additional colors available.

Applications where an insulated door with a large selection of standard colors is needed.

Available in sizes up to 36' wide x 24' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

High-performance insulated sectional door with U-Factor of 0.21 (R-Value 18.3), 2″ thickness, is engineered for enhanced energy efficiency in commercial applications.

Applications with focus on high thermal efficiency and performance.

Available in sizes up to 36' wide x 24' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

Insulated sectional steel door with 1-3/4" thick polyurethane core and 25-gauge exterior steel for durability and improved thermal performance.

Ideal for any applications that require an insulated door.

Available in sizes up to 36' wide x 24' high.

Standard hardware warranty is one year. Section warranty against delamination and rust-through is ten years.

Fire-rated rolling steel door with automatic closing for code-compliant fire separation. Provided with fusible links that automatically release to close the door at 165°F, the door’s descent can also be triggered by smoke and heat detectors, a building’s alarm system, or SS90 fail-safe devices. FireCoil fire-rated rolling doors are UL, C-UL, FM, and CSFM-labeled.

Large openings that require a fire rated door.

Available in sizes up to 30' wide.

Standard warranty is one year.

Fire-rated rolling counter shutter providing code-compliant fire protection at service openings. Provided with fusible links that automatically release to close the door at 165°F, the shutter can also be triggered by smoke and heat detectors, a building’s alarm system, or LM21 fail-safe release devices. All FireCurtain counter shutters comply with UL, C-UL, FM, and CSFM requirements for 3-hour, 1-1/2-hour, or ¾-hour fire ratings.

Any counter windows that require a fire rated counter shutter.

Available in sizes up to 12' wide and 8' high.

Standard warranty is one year.

Rolling security grille, straight or brick pattern, provides visibility, airflow, and controlled access for commercial applications. Exterior and interior applications.

Openings where security but also visibility and air circulations are important.

Available in sizes up to 35' wide and 24' high.

Standard warranty is one year.

Compact rolling counter shutter designed to secure concession and service openings.

Counter window openings.

Available in sizes up to 20' wide x 10' high.

Standard warrant is one year.

High-performance rolling steel door engineered for high-cycle durability and security.

Optimized for high-traffic environments where standard rolling steel doors lack the necessary speed and cycle life.

Available in sizes up to 20' wide x 14' high.

Standard warranty is two years or 300,000 cycles (whichever comes first).

Rolling service door. Aluminum, steel, or stainless steel slats available in multiple gauges for durable performance in commercial and industrial environments. Available with flat, insulated flat, small contour, large contour, or perforated slat profiles to accommodate functional and aesthetic requirements.

DuraCoil rolling services doors can be used in both exterior and interior applications including corrosive environments. They are also suitable for high usage applications where durability is important.

DuraCoil rolling service doors can be manufactured in sizes up to 40' wide.

Standard warranty is one year.

Custom aluminum standing-seam or interlocking panel awnings with welded frames provide durable, low-maintenance sun and rain protection at building transitions.

Specified for commercial and institutional entrances, walkways, and transitions where rigid canopy systems are required to resist wind, snow, and long-term exposure.

Not intended for applications exceeding engineered load capacities or where architectural integration requires non-standard attachment conditions without structural coordination.

Standard manufacturer warranties apply; extended warranties may be available depending on coating and finish selection.

Post-supported extruded aluminum canopy systems engineered for wind and snow loads provide economical weather protection along pedestrian walkways and entrances.

Primary entries, transit shelters, covered walkways.

Requires ground support posts.

Tensioned exterior shading and weather protection using high-performance architectural fabrics. Systems are configured for attachment to building structures and coordinated with façade assemblies and adjacent construction.

Used at building entrances, storefronts, windows, walkways, and outdoor gathering areas for sun control, rain protection, and visual identity in commercial and institutional projects.

Not intended for locations requiring impact resistance, fire resistance, or continuous snow load capacity beyond fabric system design limits.

Fabric warranties vary by selected fabric manufacturer; extended warranties greater than one year may be available depending on fabric type.

Extruded aluminum sunshade systems with horizontal or vertical louvers designed to reduce solar heat gain and glare while enhancing facade appearance.

Window walls, façades, curtain walls.

Not intended as primary weather barrier.

Warranty terms are project-specific; extended warranties may be available depending on materials and finishes.

Wall-mounted aluminum canopy providing unobstructed overhead cover. Internally supported extruded aluminum canopy with steel support arms and integrated drainage provides streamlined weather protection without ground supports.

Main entries, storefront canopies.

Requires structurally capable wall substrate.

Overhead supported extruded aluminum canopy with built-in drainage and customizable fascia and decking provides durable weather protection at building entrances and service areas.

Building entrances, walkways, exterior transitions.

Not suitable where structural support is inadequate.

CDH Palisade Security Fencing is available with three head styles. The steel picket profile is configured to reduce the potential for climbing. Pickets are mechanically fastened to horizontal support rails using break-away nuts and anti-pry bolts. Individual pickets may be replaced if damaged, without requiring removal of full fence panels. Horizontal rails are pre-punched to receive the vertical pickets and are intended for permanent installation. An anti-climb projection (“stab” feature) is located between pickets. Rails may also be specified in an anti-scale configuration with reduced picket spacing. Support posts are formed with an I-beam profile and are available in multiple heights. Posts are pre-punched to receive the horizontal rails and are intended for permanent installation.

Commercial and Industrial

See Warranty Information

StuccoDri is a water repellent, high performance, permeability reducing liquid admixture (PRA) designed for cementitious stucco. It is a liquid admixture that replaces water in the mixing process at a 1:1 ratio. Integral, permanent water resistance—built into the mix. Up to 120% permeability reduction on full-thickness stucco. Compatible with lath-applied and direct-applied stucco systems. Accepts traditional, properly applied exterior paints and coatings designed for stucco.

Corning® Med-X® LT Glass, Lemi-Thin radiation shielding/x-ray barrier. Meets Cat II Impact Ratings. Maximum finished size of up to 40" x 60". Registered as compliant with U.S. Food and Drug Administration (FDA) regulations. and McGrory Glass, Inc. is the only FDA Registered Medical Device Manufacturer; Repackager/Relabeler of FDA Registered radiation shielding glass. FDA Registered Material has a verified, traceable process linking the manufacturer to the processor to the installer to the project within the formalized format of FDA Registration. Traceability helps ensure compliance with medical device standards: at any point, from receipt to post-installation, each individual piece of Corning® Med-X® LT Glass can be traced back through its shipment, processing, and manufacture.

Corning® Med-X® Glass, lead, radiation shielding glass, dimensions up to 54" x 108". Optical Properties - Refractive Index nd: 1.76 Transmission % @ 550nm through 5mm path: ≥85.0 Mechanical Properties - Lead (Pb): 52% Barium (Ba): 17% Mechanical Properties - Density (g/cm3): 4.8 Knoop Hardness (kg/mm2): 409 Young’s Modulus (GPa): 62.6 Torsion Modulus (GPa): 24.8 Poisson’s Ratio: 0.26 Coefficient of Thermal Expansion (x10 -7 /°C): 78.8

ElectraView™, zero energy required for OBSCURE or CLEAR state. Energy Data: Input Power - 120VAC /60Hz Output Power - 48VAC /60Hz Energy Consumption - 0.3 watts/ ft2 power on | 0 Watts/ ft2 power off Power Quality - Film is protected by an isolation transformer, reducing spikes, harmonics, and noise when using ElectraView™ PDLC controller by McGrory. Operating Temperature - 0°-35°C INTERIOR ONLY

Doors and entrances, Office fronts, Hospital room dividers & Curtain walls, Emergency room / ICU sliding & breakaway doors, X-Ray privacy, Conference rooms, Laminated glass

RedHeader Lite is designed to replace conventional built-up jambs and headers while providing better results in half the time. One-piece jambs eliminate the additional studs, track and screws required to frame conventional rough openings.

Galvanized steel plate veneer anchor with vertical projecting leg protruding through continuous insulation to receive veneer triangle. Available in hot dip galvanized finish.

Masonry veneer anchor screw attached to stud framed, concrete, or masonry exterior walls. Use with or without seismic clips and continuous rods.

Install anchor before continuous wall insulation. Maximum 4.5 inch wide cavity with maximum 4.5 inch thick continuous insulation. Maximum 9 inch veneer triangle length.

Galvanized steel screw and washer anchor with projecting eye to receive hot dip galvanized steel wire tie. Available in polymer coated finish.

Masonry veneer anchor screw attached to metal and wood stud framed exterior walls with continuous insulation. Use with or without seismic clips and continuous rods.

Install anchor after continuous wall insulation. Maximum 6 inch sheathing plus insulation thickness. Maximum 7 inch veneer wire tie length.

Ladder style with projecting eyes, galvanized steel, horizontal joint reinforcing for masonry cavity wall joints. Available in standard, heavy duty, and extra heavy duty side and cross wire diameters with mill or hot dip galvanized finish.

Cavity walls with masonry veneer and concrete masonry backup at exterior walls. Use with loadbearing and non-loadbearing, ungrouted and vertically reinforced and grouted concrete masonry. Use with veneer hooks with or without seismic clips and continuous rods.

Maximum 12 inch concrete masonry wythe. Maximum 6 inch wide cavity with maximum 4 inch thick continuous insulation. Maximum 7 inch veneer hook length.

Galvanized steel triangle wire veneer tie fitted with dovetail head for insertion into dovetail slot. Available in hot dip galvanized finish.

Masonry veneer anchor for concrete and masonry substrates with or without continuous insulation. Use with or without seismic clips and continuous rods.

Requires dovetail slot cast into concrete substrate or surface mounted on concrete or masonry substrate. Maximum 5 inch dovetail triangle length.

Rebar Positioners are used to properly locate the rebar in the cores of the CMU.

Ladder style, galvanized steel, horizontal joint reinforcing for unit masonry joints. Available in standard, heavy duty, and extra heavy duty side and cross wire diameters with mill or hot dip galvanized finish.

Single wythe concrete masonry exterior walls and interior partitions. Use with loadbearing and non-loadbearing, ungrouted and vertically reinforced and grouted concrete masonry.

Maximum 12 inch concrete masonry wythe.

Type 304 stainless steel, self-adhered, laminated, flexible flashing with bonded butyl adhesive and release liner in 12 to 36 inch widths. Accessories include stainless steel termination bars, drip edges, prefabricated inside and outside corners, prefabricated end dams, and sealants.

Self-adhered masonry through wall flashing used with concrete, concrete masonry, and sheathing structural backup. Primer is not required.

Requires termination bar to secure top edge. Requires support across masonry cavity air space.

Life of wall warranty. 3GEN Masonry Products, Inc. (“3GEN”) warrants that its GENFLASH Membrane (“Product”) will be free from material defects that cause water penetration through the membrane for ten (10) years from the date of sale, subject to the terms, conditions, and limitations stated herein. This warranty applies solely to GENFLASH installed as an in-cavity wall flashing product to channel water out of weep holes, in accordance with 3GEN’s installation instructions. Other installation methods are explicitly excluded from this warranty.

Cellular polypropylene co-polymer vent to enable air flow and drainage of masonry cavity walls without insect intrusion. Available in six standard colors and two sizes to accommodate standard modular and jumbo brick head joints.

Replace brick masonry head mortar joint to create cavity wall weeps and vents. Install as weeps above flashing. Install as vents below flashing. Install with 1/8 inch set back from exterior wall face.

Prevent mortar droppings within cavity from clogging weeps.

Galvanized steel plate veneer anchor with projecting tab to receive veneer triangle. Available in hot dip galvanized finish.

Masonry veneer anchor screw attached to stud framed, concrete, or masonry exterior walls. Use with or without seismic clips and continuous rods.

Do not install anchor over continuous wall insulation. Maximum 6 inch wide cavity. Maximum 9 inch veneer triangle length.

Composite polyethylene sheet, self-adhered, flexible flashing with bonded clear adhesive in 4 to 36 inch widths. Accessories include stainless steel termination bars, drip edges, prefabricated inside and outside corners, prefabricated end dams, and sealants.

Self-adhered, self sealing, masonry through wall flashing used with concrete, concrete masonry, and sheathing structural backup. Primer is not required.

Requires termination bar to secure top edge. Requires support across masonry cavity air space.

3GEN Masonry Products, Inc. (“3GEN”) warrants that its GENFLASH Membrane (“Product”) will be free from material defects that cause water penetration through the membrane for ten (10) years from the date of sale, subject to the terms, conditions, and limitations stated herein. This warranty applies solely to GENFLASH installed as an in-cavity wall flashing product to channel water out of weep holes, in accordance with 3GEN’s installation instructions. Other installation methods are explicitly excluded from this warranty.

3, 5, or 7 oz copper sheet, laminated, flexible flashing bonded to polymeric fabric on both faces in 12 to 36 inch widths. Accessories include aluminum and stainless steel termination bars, stainless steel drip edges, prefabricated inside and outside corners, prefabricated end dams, and sealants.

Masonry through wall flashing used with concrete, concrete masonry, and sheathing structural backup.

Requires termination bar to secure top edge. Requires support across masonry cavity air space.

Life of wall warranty. 3GEN Masonry Products, Inc. (“3GEN”) warrants that its GENFLASH Membrane (“Product”) will be free from material defects that cause water penetration through the membrane for ten (10) years from the date of sale, subject to the terms, conditions, and limitations stated herein. This warranty applies solely to GENFLASH installed as an in-cavity wall flashing product to channel water out of weep holes, in accordance with 3GEN’s installation instructions. Other installation methods are explicitly excluded from this warranty.

Type 304 stainless steel, laminated, flexible flashing with bonded polymeric fabric backing in 12 to 36 inch widths. Accessories include stainless steel termination bars, drip edges, prefabricated inside and outside corners, prefabricated end dams, and sealants.

Masonry through wall flashing used with concrete, concrete masonry, and sheathing structural backup.

Requires termination bar to secure top edge. Requires support across masonry cavity air space.

Life of wall warranty. 3GEN Masonry Products, Inc. (“3GEN”) warrants that its GENFLASH Membrane (“Product”) will be free from material defects that cause water penetration through the membrane for ten (10) years from the date of sale, subject to the terms, conditions, and limitations stated herein. This warranty applies solely to GENFLASH installed as an in-cavity wall flashing product to channel water out of weep holes, in accordance with 3GEN’s installation instructions. Other installation methods are explicitly excluded from this warranty.

Dovetail shaped drainage mesh formed from open mesh, woven, structural, polymer strands. Available in four thicknesses ranging from 0.4 to 2 inches. Compressible to fit multiple cavity widths.

Fill masonry cavities above flashings to keep weep holes open by catching mortar droppings on two levels above weeps.

Prevent mortar droppings within cavity from clogging weeps.

Designed especially for commercial construction, Twin Trac has all the enhanced features of regular Structalath with the addition of eight secondary cold-rolled longitudinal wires that add strength to form a ‘track’ for convenient attachment. Twin Trac can be substituted wherever 2.5 metal lath has been specified. Structalath Twin Trac 2.5/316 is a reduced furr version that is used with 1/2″ stucco systems.

Stone Veneer, Stucco

10 Year Limited Warranty

A superior, multi-purpose expanded steel substrate for Portland cement or widely used for interior and exterior gypsum plaster and stucco & stone reinforcement. Applications include ceilings, soffits, and fascia surfaces, and under ceramic tile in wall, ceiling, and floor applications. Metal lath is useful in general purpose applications and is the best lath available for ornamental work and for flat or contoured surfaces as well as for use as a reinforcing underlay for spray-applied fireproofing.

Stone Veneer, Stucco

Structa V-TRUSS Bullnose or Straight Corner is welded wire lath corner for 3 coat stucco applications. V-TRUSS Corner is engineered to provide superior reinforcement. The unique truss design ensures a consistent "true" - straight corner with fewer sharp ends for ease of handling. The abundant nailing opportunities and twin wires create an ease of attachment and the increased rigidity promote precise corner plaster work.

Stone Veneer, Stucco

10 Year Limited Warranty